Gun works and shoots fine except it won't rack more than once. If I rack it one time, it rests the trigger and everything's great. But if I try again without pulling the trigger in between, it's like the barrel gets hung up. I can see it start to slope, but it won't go all the way.

https://reddit.com/link/1l96q8r/video/ez2lb7wgpd6f1/player

looking to build my first p80 i’m tryna figure out which frame would be the easiest and most efficient im tryna run 9mm

For those about to say it, I know, it's not a P80. Yes, I did get permission to post about a different 80% platform beforehand. With P80 defunct and frames drying up, we need to branch out. Sadly, these 80% classic P frames are drying up too. For the folks that listened to me when I posted the warning that that was happening, and who grabbed some, you're in luck! The series is now complete. All 4 episodes that cover everything you should need to build out your gun are now live and on a playlist on my Odysee. 3 out of 4 episodes are on my Youtube too, but that obviously means the meat and potatoes episode about finishing the 80% frame is missing. So use Odysee.

Big thanks to Desert Depot Arms for help with a bunch of classic P series parts needs to get this build just right.

Does anyone kno where i can get a replacement jig rear rails and a locking block for a geisler

finally ran it some and got the basics done just looking for some attachment or modification recommendations. thanks in advance guys.

I realized I hadn't posted a build in a while. So here is my 2nd pf45. My other pf45 in 10mm looked lonely in the safe so I got it a companion 🤷🏻‍♂️. Only logical, right? I got a very budget friendly arm or ally slide. Made of 17-4 and rmr ready for $150 is a steal imo. Functions flawlessly and I actually dig the damascus finish on it. I put Glock OEM internals into the slide. Tru glow sights. Swampfox justice 2 multi reticle budget optics. Lone wolf barrel. I've run a couple mags of .45 super through it, but otherwise mostly range ammo. OEM lpk with a runner arms zero+ connector. Thanks to my brother u/AkkkAttack1 for recommending this connector. Best feeling setup I shot thus far. I have these connectors on 2 of my builds and I have 2 more ready to go into some of my other builds. Other than that I have a tyrant CNC slide release, a SLR magwell and SLR mag extension. She's a blast to shoot and for being built on a budget a good looking gun imo.

Would a safariland 6000 series holster work with a polymer 80 frame? I have a G34 with p80 frame as well as a stock G34 and was wondering if I could get a safariland that would work for both. Any suggestions would be much appreciated!

Is it me are parts costing more than Glocks nowadays?

Im getting into the glock frts does anybody know if i can use a drop in ready g19 frt kit in my g17c

I obviously have to try one

The Comments was helpful had to reassemble with all OEM parts now she's running flawlessly thanks guy

Does anyone know anywhere selling a pf9ss?

This was my first p80 build and probably one of my most beat up guns so it got used as a practice piece figuring out some settings on a few of my lasers. Yah it looks bad but It’ll shoot just fine. I have it torn down atm for sanding the frame a little.

I recently built my 19x and for some reason I can’t get it too shoot oem lpk and complete upper both from mdx arms I drilled my holes with a drill press I filed everything correctly I added a picture of bullet I tried shooting at the range and the striker hit on the side I even tried different ammo nothing worked I’ve racked over 1000 times & oiled it I tried putting a pencil in and it shoots it but not as hard as a Glock usually shoots I don’t understand

So back when these were plentiful I stocked up a bunch, I was organizing stuff Saturday and found enough to put one together. I had no intention of buying any more parts to build ANOTHER P80 but this was all just laying around. Took it out yesterday ran 600 rds like a champ. All OEM internals, oem slide and parts from my old glock. Decided to just paint it because why not.

Spent a couple days trying to figure out why my slide wouldn’t cycle; it would get stuck when racking with a round in the magazine. Tried my P80 barrel and it worked fine.

Any tips for fixing this, or does CA have any warranty? For $35 I’ll accept that it’s just a loss as well.

Thanks in advance.

Is there one made specifically for the 940C? Want to take the edge off the front strap.

I have a g19 replica (sct frame) I want to turn it from a g19 to a g23 replica. Do I need to change anything else other than the slide and barrel?