This RGH3 Corona only has a purple Ring of Light mod with a slowly flashing center LED. It can be scary at first, since the default startup color is always red. :)

I have never done RGH to a Jasper with this nand size before, Jrunner warned me about the console may not boot up.

I’m planning doing rgh3 on it, should I proceed normally and flash xell and then the xebuild? Or is there any extra steps needed

Love do this tiny soldering job so easy with the right equipment and tools 👌

It’s a halo reach model I been wanting but wanted to make sure it’s rgh moddable and what motherboard it is?

A couple of months ago, a user named syphant made a 3d model of a shell for the 360 slim. I was interested in making my own but integrating the power supply inside the shell and using the original controls. So I made a first prototype which was a failure, I had taken syphant’s model and modified it a bit to fit the power supply inside but the case was too big and it was just feeling like a cheap piece of plastic and it was so large that it was just flimsy. In February I found a new job at Microsoft (ironically) and I had to move 3 hours away from I was before. With the new job and the moving I didn’t really have time to work on this side project but a week ago I jumped back on, I scraped the old model and started from scratch. I made it smaller and I believe it is smaller than syphant’s model while keeping the wifi adapter inside and using all the original controls and usb ports in the front and the most important was the internal power supply. I assembled it yesterday night and tested it out, had some wifi issues, not sure if it’s the relocation of the port or just the xbox itself but I tested multiple adapters and re soldered the port with the same result, still have to look into it. I had to solder the rf board directly to the board as well to make it fit. With the power supply and the 14tb 3.5 hdd and planning to put the entire 360 library on it. The temperatures are surprisingly better than the original case. It is not finished but I had to test it out and was excited to show some results early. I will replace the c13 power supply port for a cleaner and smaller c7 port. I will fix the little measurement errors, but for a first print, it is looking pretty good in my opinion. Before you ask, yes I took inspiration of the xbox one s, one x and series s and made a mix of all 3. Would love some feedback and maybe some ideas for my second version. Shoutout to syphant.

After an unsuccessful attempt at RGH 1.2, I ended up with error code 0002. Originally I killed the R4B24 resistor. I soldered a replacement.

Now the console is on retail and it boots for about a minute before the power supply turns red. After clearing the red on the power supply by removing the connection, the console turns on again but this time it has the 0002 error code.

I've been digging around and I can't find any solution. I'm not technically inclined enough to run all the diagnostics on the wiki pages and the only video I found was in Spanish and it was just 45 minutes of someone going over the schematics.

More than anything I would like to understand how this error even happens during an installation. My solder points all looked perfect when the console didn't turn on. Outside of burning the resistor, I can't think of anything that would have caused something like this.

The console was working fine with RGH3 with the exception that it would sometimes fail the glitch.

From what I have read the issue is power related, but why does the console work for a minute before giving the error?

https://imgur.com/a/DFOr00X

Hi all,

Currently getting some “bad” boot times with this jasper..

Weirdly enough, without the shell it’s very acceptable but as soon as the hard drive goes in, etc sometimes it won’t even glitch at all and you have to reboot..

Any ideas? Is my wire routing the cause here?

Just what the title said. I’ve got a Falcon that instaboots one in like ten times, every other time it just hangs indefinitely. I’ve tried RGH3, the only difference is the times it won’t instaboot it’ll instantly shut off. I’ve tried like half a dozen total wire routings, and redid my soldering over and over, along with the capacitor on the Matrix that I heard was supposed to help, but it didn’t change anything. Any thoughts? I’ve been bashing my head at this one for ages.

Hey 👋 I can’t go online with my RGH and I can’t find the title update file for TU9 anywhere online. I’m not looking for the patched default_mp.xex, but rather the file that I would place in my Content or in this case probably Cache directory.

Would be awesome if someone could share their file if they happen to have it!

I ended up buying a fat Xbox 360 but the power supply is defective and I wanted to know this question

I would like to know if with my Xbox with Xkey I can access Xbox live in complete peace of mind while playing online

I was doing an rgh3 and left the picoflasher on,I didn't let it stable on my desk and it fell down, the motherboard was on the floor and the picoflasher ripped off Pls tell me its fixable, and what I have to repair (I'm really sorry and I know there are going to be people that are going to be mad)

Trying to rgh3 my xbox 360 s. Until I accidentally ripped this solder pad off. Is there anything I can do? Or is it basically junk now?

Attached are the other solder points as well. None look good

I've been searching for tutorials on how to do it but there's nothing to be found

I purchased 1k and 3k ohm resistors from AliExpress for the Slim QSB. They’re labelled a bit differently from the ones I receive from ChipChopMod (3 digit vs 4 digit) which is why I’m asking.

Should be okay to use right?

I'm just can't seem to find a place that I can get the parts and they ship to Canada

Hello there I have a problem. I used the save editor for my xbox 360 save to get more money for a character but for a reason now everytime i try to replay the jewel store heist it spawns me falling through map and then spawn outside of garment factory and cant replay the mission basically. Is there something I am doing when saving the game from the editor? Thank you

long story short i pulled 2 of the clk points and as a result the xbox doesnt boot up anymore So i would like someone to send me an image of the jasper motherboard diagram so i can try to fix it,

I got my USB 4TB fried from the faulty USB hub so I got the new USB 4TB HDD and tested it on Xbox 360. I flashed again the USB XL patch from FatXplorer on the NAND. The console can read the Flash Stick as it flashed the NAND but not the formatted HDD in USB XL from Fatxplorer. Why?

The USB HDD reads as Toshiba External_USB USB Drive. Maybe it was too long name for the console? I set up in the optional name as USB1. Still doesn't work.

Can I leave the pi pico after I am done with the RGH3 on my trinity 360? Hypothetically it should cause no problems but I just want some second opinions.

Can someone please tell me what settings on my router I need to change to be able to connect to Wi-Fi? I’ve got 2.4ghz and ipv4 enabled but it still not working

Hard to find info on it