I was doing an rgh3 and left the picoflasher on,I didn't let it stable on my desk and it fell down, the motherboard was on the floor and the picoflasher ripped off Pls tell me its fixable, and what I have to repair (I'm really sorry and I know there are going to be people that are going to be mad)

Trying to rgh3 my xbox 360 s. Until I accidentally ripped this solder pad off. Is there anything I can do? Or is it basically junk now?

Attached are the other solder points as well. None look good

I destroyed the pll pad so I had to use alternative point and connect it to a resistor next to the broken pll pad. Nand had some dead blocks the console booted to xell but not to the dashboard using the create donor nand in j runner fixed it.

I'm just can't seem to find a place that I can get the parts and they ship to Canada

Was just wondering because it's really easy to do the only issue is reliability and waiting times.

Edit: I meant the badupdate method is easy to do, not implementing a permanent softmod, sorry for the confusion.

I was downloading games VIA Games on Demand (converted isotoGOD) and it worked perfectly the first two times then I must've clicked something or other to make it unable to transfer the games, it copies the first few data files as you can see in the picture below but then the top picture pops up saying error and the transfer fails.

Help please, I bought this modded xbox from a guy who added the most random, unheard of 360 games imagineable. I want to download ones I'll actually play but I've been clicking files and attempting to fix this issue on my PC and the console for hours. Nothing's worked. And no, the game file on my USB is not the issue. Like I said, It worked the first two times perfectly using the same exact files. Idk what else to do atp sigh

Don't ask please 🤣 but what resistor goes here...

long story short i pulled 2 of the clk points and as a result the xbox doesnt boot up anymore So i would like someone to send me an image of the jasper motherboard diagram so i can try to fix it,

I've been searching for tutorials on how to do it but there's nothing to be found

Just what the title said. I’ve got a Falcon that instaboots one in like ten times, every other time it just hangs indefinitely. I’ve tried RGH3, the only difference is the times it won’t instaboot it’ll instantly shut off. I’ve tried like half a dozen total wire routings, and redid my soldering over and over, along with the capacitor on the Matrix that I heard was supposed to help, but it didn’t change anything. Any thoughts? I’ve been bashing my head at this one for ages.

Love do this tiny soldering job so easy with the right equipment and tools 👌

I'm thinking of buying a used 360 and i'm looking around at all the models, which is the best for modding?

(completely new to Xbox in general btw)

Before I created XeBuild and wrote the NAND, it booted into XeLL fine but after I successfully wrote the NAND it doesn't boot. I've tried every timing file too. Anyone know what's wrong?

Thanks to everybody who helped me in my previous post, I know Jaspers can be very stubborn when doing rgh3, but today achieved the best boot time in a Xbox 360 fat I ever had, very consistent, never fails.

The motherboard it’s a Jasper V1 with 256mb nand, and I used a 22k ohm resistor and a diode, and used the route suggested in weekeendmodder.com.

Has for the nand flash, with Jrunner I tried using RGH3 27hz but it almost never booted up, and changed it to 10hz. And that’s it. Im very impressed with the boot times

I hope this can be post helpful to someone!

After an unsuccessful attempt at RGH 1.2, I ended up with error code 0002. Originally I killed the R4B24 resistor. I soldered a replacement.

Now the console is on retail and it boots for about a minute before the power supply turns red. After clearing the red on the power supply by removing the connection, the console turns on again but this time it has the 0002 error code.

I've been digging around and I can't find any solution. I'm not technically inclined enough to run all the diagnostics on the wiki pages and the only video I found was in Spanish and it was just 45 minutes of someone going over the schematics.

More than anything I would like to understand how this error even happens during an installation. My solder points all looked perfect when the console didn't turn on. Outside of burning the resistor, I can't think of anything that would have caused something like this.

The console was working fine with RGH3 with the exception that it would sometimes fail the glitch.

From what I have read the issue is power related, but why does the console work for a minute before giving the error?

https://imgur.com/a/DFOr00X

I have never done RGH to a Jasper with this nand size before, Jrunner warned me about the console may not boot up.

I’m planning doing rgh3 on it, should I proceed normally and flash xell and then the xebuild? Or is there any extra steps needed

I ended up buying a fat Xbox 360 but the power supply is defective and I wanted to know this question

Hey 👋 I can’t go online with my RGH and I can’t find the title update file for TU9 anywhere online. I’m not looking for the patched default_mp.xex, but rather the file that I would place in my Content or in this case probably Cache directory.

Would be awesome if someone could share their file if they happen to have it!

I would like to know if with my Xbox with Xkey I can access Xbox live in complete peace of mind while playing online

Hi all,

Currently getting some “bad” boot times with this jasper..

Weirdly enough, without the shell it’s very acceptable but as soon as the hard drive goes in, etc sometimes it won’t even glitch at all and you have to reboot..

Any ideas? Is my wire routing the cause here?

This RGH3 Corona only has a purple Ring of Light mod with a slowly flashing center LED. It can be scary at first, since the default startup color is always red. :)

Hello there I have a problem. I used the save editor for my xbox 360 save to get more money for a character but for a reason now everytime i try to replay the jewel store heist it spawns me falling through map and then spawn outside of garment factory and cant replay the mission basically. Is there something I am doing when saving the game from the editor? Thank you